Matric Limited
  • 24-Jan-2017 to 14-Jun-2017 (EST)
  • 414/418 AfterMarket Services
  • Seneca, PA, USA
  • $13.00 to $19.50
  • Hourly
  • Full Time

medical, dental, vision, life insurance, 401k


This is a day shift position.  Core hours are Monday through Friday, 7:00 a.m. to 3:30 p.m.

DUTIES AND RESPONSIBILITIES:
Other duties may be assigned.
1. Visually inspect assemblies to determine if they are built to customer specifications.
2. Perform electronic testing of assemblies.
3. Be able to disassemble and re-assemble units correctly.
4. Perform basic electronic/ functional troubleshooting for assemblies that do not pass the accepted test procedures.
5. Identify faulty components, components installed incorrectly, and detect other quality defects.
6. Adjust or replace defective components to meet established standards.
7. Identify, prepare and correctly solder components to PC board. Become solder certified.
8. Assemble prototype units.
9. Maintain accurate records on paper and/or computer.
10. Show competency in Matric Limited part numbering system.
11. Determine the priority of the scheduled work and adjust to changes daily.
12. Shall practice safe work habits and report all safety hazards to the supervisor.
13. Shall be responsible for inspecting your work and identifying quality defects.
14. Be accountable for the quality and quantity of your work.
15. Assist co-workers with problems encountered.
16. Shall be instrumental in improving processes and in creative problem-solving.
17. Be familiar with company operations and regulations.
18. Help to maintain good morale within the department.

NOTE: The preceding examples are representative of the assignments performed by this position and are not intended to be all-inclusive.

QUALIFICATION REQUIREMENTS:  To perform this job successfully, an individual must be able to perform each essential duty satisfactorily.  The requirements listed below are representative of the knowledge, skill, and/or ability required.  Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Shall be familiar with and able to use the following hand tools: screwdriver, pliers, wire cutter, wire stripper, various small wrenches, etc.
Able to read and interpret engineering drawings, schematic diagrams, and formulas and confer with management or engineering staff to determine quality and reliability standards.
Be able to utilize the following test equipment for inspection and troubleshooting, and verify that it is operational and within calibration: Volt/ohm/milliammeters, oscilloscopes, signal generators, frequency counters, waveform generators, power supplies, various analog and digital tests sets, EPROM/PLD programmers, cable autotesters, and proprietary test equipment as needed.
Have a general knowledge of warehouse operations.
Able to work with speed and accuracy in assigned tasks.
Able to communicate effectively and relate to co-workers.
Able to professionally handle communications with customers and vendors.
Must be able to use computer properly for retrieving/ storing data.
Shall be able to follow verbal instructions and function with minimum guidance.
Shall maintain a neat appearance about self and work areas.
Shall be presentable to customer at all times.

EDUCATION AND/OR EXPERIENCE:  

High school or GED.  Accepted electronics training - degree, technical certificate, vocational schooling and/or accepted correspondence course.

PHYSICAL DEMANDS:  The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Must be able to lift up to 50 pounds.
Must have visual acuity to read prints and interpret color codes on wires and components:
Near Vision: Jaeger 1 at 35.5 cm (14 in.), reduced Snellen 20/20 or equivalent - testing both eyes together
Far Vision: Snellen 20/30 minimum when testing both eyes together.
Color Vision: average

Matric Limited
  • Apply Now

  • * Fields Are Required

    What is your full name?

    How can we get a hold of you?

    By clicking the button above, I agree to ApplicantPro's Applicant Information Use Policy.

  • Sign Up For Job Alerts!

  • Share this Page
  • Facebook Twitter LinkedIn Email
.
Logo email Request a Quote Contact Us Conflict Minerals Statement My Account About Us Electronic Manufacturing Services Products Quality News Events